STLink - Revision history

Dsojka at 22:24, 29 May 2018

2018-05-29T22:24:03Z

2018-05-29T22:23:35Z

2018-05-29T21:58:28Z

2018-05-29T16:37:00Z

2018-05-29T16:12:41Z

2018-05-29T16:12:07Z

2018-05-29T16:11:35Z

2018-05-29T16:08:09Z

2018-05-29T16:07:49Z

2018-05-25T22:26:40Z

@@ Line 58: / Line 58: @@
 . Once installed, you can simply open a terminal and issue the following commands:
 * To erase the chip:
-** {{cli | username=developer | hostname=linux | st-flash erase }}
+** {{cli | username=developer | hostname=linux |st-flash erase }}
 * To program board using a hex file:
-** {{cli | username=developer | hostname=linux |  st-flash --format ihex write filename.hex}}
+** {{cli | username=developer | hostname=linux |st-flash --format ihex write filename.hex}}
 * To program a board using binary files:
-** {{cli | username=developer | hostname=linux | st-flash write firmware0.bin 0x08000000 }}
+** {{cli | username=developer | hostname=linux |st-flash write firmware0.bin 0x08000000 }}
-** {{cli | username=developer | hostname=linux | st-flash --reset write firmware1.bin 0x08020000 }}
+** {{cli | username=developer | hostname=linux |st-flash --reset write firmware1.bin 0x08020000 }}
 <!-- /*********************************************************************************************************/ -->

@@ Line 58: / Line 58: @@
 . Once installed, you can simply open a terminal and issue the following commands:
 * To erase the chip:
-** test
+** {{cli | username=developer | hostname=linux | st-flash erase }}
 <!-- /*********************************************************************************************************/ -->

@@ Line 17: / Line 17: @@
 {{:Templateimpl:geninfo | initials=BS | title=STLink | desc=The following page can be used to get familiarized with STLink on EMAC products. | project=OE 5.0 }}
 === Tools Required ===
 === Setup ===
 <!-- /*********************************************************************************************************/ -->
 <!-- /*****************************************  Using/Working With  ******************************************/ -->
@@ Line 48: / Line 54: @@
 <!-- /*********************************************************************************************************/ -->
 {{:Templateimpl:using | initials=BS | title=STLink on Linux | desc=The following page can be used to get familiarized with STLink on EMAC products. | project=OE 5.0 }}
 <!-- /*********************************************************************************************************/ -->

@@ Line 38: / Line 38: @@
 . In the upper left, click 'Target', then 'Program & Verify'. The following window should appear. Click 'Start'.
 [[File:STLinkProgram.PNG|800px|thumb|left|STLink Program]]
 <br clear=all>

@@ Line 25: / Line 25: @@
 Open the STLink Utility
-[[File:STLinkUtility.PNG|500px|thumb|left|STLink Utility]]
+[[File:STLinkUtility.PNG|800px|thumb|left|STLink Utility]]
 <br clear=all>
 Click on the 'Binary File' tab in the upper left. A file browser should appear. Navigate to the directory that contains the binary file you plan to use and click 'Open'
-[[File:STLinkFileBrowse.PNG|500px|thumb|left|STLink File Browse]]
+[[File:STLinkFileBrowse.PNG|800px|thumb|left|STLink File Browse]]
 <br clear=all>
 [Optional] Before programming the unit, it is recommended to erase the chip. In the upper left, click 'Target' and then click 'Erase Chip'. You should see the following message if it completes successfully.
-[[File:STLinkEraseChip.PNG|500px|thumb|left|STLink Erase Chip]]
+[[File:STLinkEraseChip.PNG|800px|thumb|left|STLink Erase Chip]]
 <br clear=all>
 . In the upper left, click 'Target', then 'Program & Verify'. The following window should appear. Click 'Start'.
-[[File:STLinkProgram.PNG|500px|thumb|left|STLink Program]]
+[[File:STLinkProgram.PNG|800px|thumb|left|STLink Program]]
 <br clear=all>