Difference between revisions of "Custom Linux Kernel Development"
(fixed source code) |
(initial driver development content) |
||
Line 397: | Line 397: | ||
After making the development changes required to support a new carrier board, you must change the kernel configuration to specify the new carrier board. Using the menu configuration utility described in the [[#Menuconfig|Menuconfig section]], navigate to 'System Type -> Atmel AT91 System-on-Chip -> EMAC Carrier Board Selection''. The list should now have a choice for ''NPD Carrier Support''. Highlight this option and press enter. Finally, exit and save the configuration. | After making the development changes required to support a new carrier board, you must change the kernel configuration to specify the new carrier board. Using the menu configuration utility described in the [[#Menuconfig|Menuconfig section]], navigate to 'System Type -> Atmel AT91 System-on-Chip -> EMAC Carrier Board Selection''. The list should now have a choice for ''NPD Carrier Support''. Highlight this option and press enter. Finally, exit and save the configuration. | ||
− | Following the steps described in [[#Building and Deployment]] above, compile the kernel and load it to your target hardware. Test all functionality, particularly new devices that were added to the carrier board support file, and make adjustments as necessary. | + | Following the steps described in [[#Building and Deployment|Building and Deployment]] above, compile the kernel and load it to your target hardware. Test all functionality, particularly new devices that were added to the carrier board support file, and make adjustments as necessary. |
== Driver Development == | == Driver Development == | ||
− | + | Device drivers provide a direct interface to a hardware device through a well-defined standard programming API. This makes the device accessible to userspace and other kernel code without requiring any knowledge of what is happening at the hardware level. For example, a CAN bus controller may be memory mapped to the processor, while another connects through the SPI bus. The user does not need to know which method is used, the CAN API is used to abstract this and the same application code may be used with either device. Furthermore, the driver for the SPI-based CAN chip may be used on different systems without porting as it uses the standard SPI API to interface with the SPI controller through the SPI driver written for the processor it is being used on. Developing and examining device driver code is often required through the course of embedded systems development, particularly due to the specialized devices used. This section provides a quick overview of device driver development on the Linux Kernel. | |
+ | |||
+ | === Driver Structure === | ||
+ | |||
+ | As an open source operating system, all of the source code for device drivers on the system (except for any proprietary binary modules as discussed in [[#Licensing|Licensing]] below) are available for reference and analysis. | ||
+ | |||
+ | === Driver Development Process === | ||
== Licensing == | == Licensing == |
Revision as of 08:01, 5 February 2014
The ability to easily customize and expand any portion of the kernel is a feature of Linux that makes it very well suited for embedded systems development. In the embedded environment, specialized hardware, protocols, and systems may require a look into the kernel internals, custom configuration, feature additions, or driver development. This article aims to provide information on the most common kernel development tasks for EMAC OE Linux systems. In addition, the reader is pointed to sources for kernel development resources.
Contents
- 1 Prerequisites
- 2 Background
- 3 The Kernel Source
- 4 Configuration
- 5 Adding Support for a New Carrier Board
- 6 Driver Development
- 7 Licensing
- 8 Where to go for Additional Information
Prerequisites
This article assumes some basic familiarity with Linux and C programming competency. Before continuing, make sure that git is installed on your development machine, and review the Building the Linux Kernel document.
Background
Maybe some more here about the technical design of the kernel and very brief history... monolithic kernel, loadable modules, etc. For now just see wikipedia http://en.wikipedia.org/wiki/Linux_kernel
The Kernel Source
Source code for EMAC kernels is provided through our Git server. Refer to the documentation for your system to determine the correct source to use.
For this guide, the 2.6.30-at91 kernel tree will be used, which currently covers many of EMAC's SoM-based ARM products. |
Clone the Git Repository
To clone the git repository over anonymous HTTP, run the following commands:
developer@ldc:~$ git clone http://git.emacinc.com/public/source/linux-2.6.30-at91.git
Once the command has completed, the entire source should be contained in the linux-2.6.30-at91
directory. The master branch will be checked out automatically. Because EMAC uses the master branch for all releases, this is the correct branch to use, but other branches or tags may be checked out if directed or required.
Kernel Source Structure
Within the kernel source tree that was downloaded, you will see several directories. Table 1 gives a brief description of each of these directories.
Directory name | Description |
---|---|
arch |
Architecture-specific kernel code with subdirectories for each architecture |
block |
Block device driver code |
crypto |
Encryption support algorithms |
Documentation |
Text documentation files on the kernel and APIs |
drivers |
Device driver code, with a subdirectory structure for each device type |
firmware |
Code for building firmware required to communicate with devices |
fs |
File systems code |
include |
Include (header) files required to build the kernel code |
init |
Kernel initialization code |
ipc |
Interprocess communications code |
kernel |
Main internal kernel code |
lib |
Library code |
mm |
Memory management code |
net |
Kernel networking code |
samples |
Code examples and drivers that have not been fully developed |
scripts |
Various scripts used for the configuration and build process as well as standalone utility scripts |
security |
Kernel security support |
sound |
Sound and audio driver code |
usr |
Code used during kernel image creation |
virt |
Virtualization support code |
These directories will be referred to as needed in this document.
Configuration
The kernel uses a configuration system that specifies how every aspect of the kernel is built.
Configuration Structure
The kernel configuration is generated based on selections by the user combined with dependency information built into the Kconfig structure. You will find a file named Kconfig
in most source directories within the kernel. These files follow the language described in Documentation/kbuild/kconfig-language.txt
and control the structure and operation of the kernel configuration utility.
The current kernel configuration is stored in a file named .config
in the top level of the kernel source tree. This file is read and updated by the configuration utility and is used by the make system during the build process. The first step in configuring the kernel often involves initializing this file with a default configuration set up with sane values for the target platform. These default configuration files are stored under the arch
directory. For example, arch/arm/configs/
.
Note that the .config file is a hidden file since its filename begins with a '.' . The ls utility will not show this file by default unless the -a option is passed to show hidden files. |
In this example, copy the arch/arm/configs/som9g45-som210_defconfig
file to the top level of the kernel source as .config
:
developer@ldc:~$ cp arch/arm/configs/som9g45-som210_defconfig .config
This is the default configuration file for the EMAC SoM-9G45 module using an SoM-210ES carrier board.
The configuration file defines all CONFIG
values that are set, either y (yes), m (module), a numeric value, or a string value. Options not configured are entered into the file as a comment with the option followed by the words "is not set." An example of each of these formats is shown below:
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.30
# Tue Jan 10 17:42:58 2012
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_MMU=y
# CONFIG_NO_IOPORT is not set
...
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
...
CONFIG_INIT_ENV_ARG_LIMIT=32
...
CONFIG_SDIO_UART=m
While editing the configuration file by hand is not recommended because it is easy to break dependencies that the configuration utility will catch, viewing the configuration file as text can be helpful in quickly viewing the current configuration selections. |
Configuring the Kernel
The kernel supports several methods of generating configuration values including command line utilities, a menu-based utility, a Qt-based utility, and a GTK+-based utility. These utilities are instantiated as make
targets. The menu-based utility, invoked by the menuconfig command is the only option supported by the EMAC Linux kernel build script. See here for more information on how to initiate the configuration process using the EMAC Linux kernel build script.
Menuconfig
The top-level interface to the kernel menuconfig utility is shown in Figure 1. Note that the navigation keys and legend are shown at the top of the page.
Any menu item with a ---> will lead to a submenu with further options. For example, to set the EMAC carrier board used with this SoM, you would use the arrow keys to highlight System Type and press Enter to select. From this menu, select Atmel AT91 System-on-Chip followed by EMAC Carrier Board Selection. This will initiate a menu allowing a single selection with all of the carrier boards supported by the currently selected SoM module. If, for example, you wanted to target the SoM-200ES carrier board, you could highlight SOM-200ES Carrier Support and press the space bar or Enter to select.
Once all desired changes have been made, select Exit and press enter from the main menu. You will be prompted to save the kernel configuration as shown in Figure 2.
Building and Deployment
If configuration options are the only customization required for your project, you may continue by building the kernel. If only loadable module options were changed from the original configuration that your running kernel was built with, you will only need to load the modules onto the target system as described here. If other built-in options were modified, you will need to reload the kernel image as well, which requires a different procedure depending on the bootloader. More here links for different bootloaders
Adding Support for a New Carrier Board
One common kernel development task working with EMAC systems is adding support for a new custom carrier board for use with an EMAC SoM. In general, the procedure for this task is to use one of the existing EMAC carrier board support files as a base and modify as needed to support the custom hardware. Additions to the Makefiles and Kconfig are also generally required to add new selections to the kernel configuration and build system. This section covers an example of the work required for this using the SoM-9G45 module as an example.
Note that the process described below is somewhat tailored to the 2.6.30-at91 kernel tree and will not be applicable directly to systems which use different kernels without some modification. The intent is to familiarize the task of adding support for a custom carrier board using this as a specific example. Contact EMAC if you require more information on how to do this for your target system. |
Machine-Specific Support Files
Board-level support files are found under the machine-specific directories within the kernel structure for ARM devices. For the Atmel AT91-based devices, this is found under arch/arm/mach-at91
. Within this directory, you will see some CPU-specific support and includes, as well as a collection of files prefixed with board-
. These files contain configuration and initialization code to support a specific board -- only one of which may be included in a single kernel binary.
The board support file for the SoM9G45 is board-som9m10g45.c
. Looking at this file, you will see that it contains code for devices inherent to the module, such as the flash, LCD, Ethernet PHY, micro-SD (MMC), and others. You will also notice references to the cspec
("carrier specification") structure. This structure is defined by code in the carrier board file and determines which devices are enabled and how they are configured to match the features of the target carrier board.
Note that this method of board support configuration changed dramatically in more recent kernel series with the Device Tree structure. |
For example, in the som_board_init()
function, SPI support is configured with the following lines:
/* SPI */
at91_add_device_spi(som_spi_devices, ARRAY_SIZE(som_spi_devices));
if (cspec.use_periph & CARRIER_USES_SPI)
at91_add_device_spi(cspec.carrier_spi_info, cspec.carrier_spi_cnt);
The first call to at91_add_device_spi()
adds devices present on the SoM itself, while the next lines check to see if the carrier board specification indicates that SPI is utilized, and if so the devices in the carrier board spi configuration are added. The carrier support functions and definitions are included through arch/arm/mach-at91/include/mach/emac-carrier.h
.
Carrier Board-Specific Support
The emac-carrier
directory contains code and configuration specifically for support of EMAC carrier boards. This code is used to generate the carrier specification values used in the board-som9m10g45.c
file as shown above. The Kconfig
file in the emac-carrier
directory is sourced from the mach-at91/Kconfig
file and provides selections for all available carrier boards. A snippet of the emac-carrier/Kconfig
file is shown below.
if MACH_SOM9M10G45
choice
prompt "EMAC Carrier Board Selection"
....
config SOM200_CARRIER
bool "SOM-200ES Carrier Support"
config SOM210_CARRIER
bool "SOM-210ES (PPC-E4) Carrier Support"
config SOM212_CARRIER
bool "SOM-212ES Carrier Support"
config SOM250_CARRIER
bool "SOM-250ES (PPC-E10/PPC-E7+) Carrier Support"
endchoice
This generates the selection menu discussed in the Menuconfig section. If "SOM-210ES (PPC-E4) Carrier Support" is selected in the menu, the variable CONFIG_SOM210_CARRIER
will be defined. Looking at emac-carrier/Makefile
, you will see entries for each carrier board as well as other related options. For example, the line below specifies that board-som210.c
will be compiled and included in the image if the SOM-210ES carrier support option is selected.
obj-$(CONFIG_SOM210_CARRIER) += board-som210.o
Taking SOM-210ES as an example, look at the board-som210.c
. You will see a good portion of software that is very similar to the full board support files in the mach-at91
directory, since this file defines all peripheral support required by the carrier board hardware not included in the base code for the SoM itself. At the bottom of the file, you will find the carrier_init()
function, which is called from the SoM initialization code and sets up the carrier_spec
struct. This function is shown below for review:
int __init carrier_init(struct carrier_spec *spec)
{
spec->use_periph = CARRIER_USES_USBH | CARRIER_USES_MCI | \
CARRIER_USES_TSADCC | CARRIER_USES_PWM | \
CARRIER_USES_LCD | CARRIER_USES_SPI | \
CARRIER_USES_I2C0;
spec->carrier_map_io = carrier_map_io;
spec->carrier_boardspec = carrier_device_boardspec;
spec->carrier_spi_info = carrier_spi_devices;
spec->carrier_spi_cnt = ARRAY_SIZE(carrier_spi_devices);
return 0;
}
Note that some of the carrier_spec
parameters are function pointers, such as spec->carrier_map_io
and spec->carrier_boardspec
.
Example New Carrier Board Support Files
Suppose that support for a new carrier board is required and utilizes hardware very similar to the SoM-210ES. For the purposes of this example, assume that the name of the product is "NPD." Start by copying the emac-carrier/board-som210.c
file to emac-carrier/board-npd.c
and follow the steps below to add support to the kernel for this new board.
developer@ldc:~/linux/arch/arm/mach-at91/emac-carrier$ cp board-som210.c board-npd.c
Kconfig and Makefile Additions
An entry must be added to the Kconfig
file in order for it to be an available option in the configuration menu. To do this, edit emac-carrier/Kconfig
and add the entry as shown below under the EMAC Carrier Board Selection selection menu.
if MACH_SOM9M10G45
choice
prompt "EMAC Carrier Board Selection"
config NPD_CARRIER
bool "NPD Carrier Support"
....
endchoice
A corresponding Makefile entry is required to trigger compilation and linking of the board-npd.c
file that was created when the CONFIG_NPD_CARRIER
option is selected. Add the following line to emac-carrier/Makefile
:
obj-$(CONFIG_NPD_CARRIER) += board-npd.o
Source Code Modifications
The final step in adding support for the NPD carrier board involves modifying the C source in the emac-carrier/board-npd.c
file that was created to match the hardware. As this is a fictional product, the modifications below will make assumptions as to what features are included.
Serial Support
The carrier_map_io()
function performs initialization and mapping of the serial ports on the system. The SOM210 carrier has three serial ports using the DBGU, USART1, and USART2 controllers. Assume that the NPD system has one additional serial port mapped to USART3 on the CPU with no handshaking. The resulting code is shown below.
static void __init carrier_map_io(void)
{
/* DGBU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
at91_register_uart(AT91SAM9G45_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_register_uart(AT91SAM9G45_ID_US2, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_register_uart(AT91SAM9G45_ID_US3, 3, 0);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
SPI Support
The next section in the carrier board file specifies the SPI devices on the system. Assume that the NPD carrier board will have support for the CS4271 audio codec and one spare general purpose SPI software interface. The AD7766 SPI device in the SoM210ES carrier board file will not be required. The resulting SPI specification is as follows:
static struct spi_s spi0cs1 =
{
.name = "spi0cs1",
.subclass = 0,
.tip = lsi2esc_spi_tip,
.xmit = lsi2esc_spi_xmit,
.confwrite = lsi2esc_spi_confwrite,
.confread = lsi2esc_spi_confread,
.speedread = lsi2esc_spi_speedread,
.speedwrite = lsi2esc_spi_speedwrite,
.gpio_name = NULL,
.gpio_create = NULL,
.gpio_data = NULL,
};
static struct spi_board_info carrier_spi_devices[] = {
#if defined(CONFIG_SND_SOC_CS4271) || defined(CONFIG_SND_SOC_CS4271_MODULE)
{ /* CS4271 codec */
.modalias = "cs4271",
.chip_select = 2,
.bus_num = 1,
.max_speed_hz = 1 * 1000 * 1000,
},
#endif
{ /* SPI0 CS1 (Spare) */
.modalias = "lsi2esc",
.chip_select = 1,
.controller_data = (void *)AT91_PIN_PD28,
.bus_num = 0,
.max_speed_hz = 1e6,
.platform_data = &spi0cs1,
},
};
Note that the spi0cs1 device is an EMAC SPI Class device. See EMAC SPI Programming for more information on how to utilize this interface. |
Programmable Clocks
The next function in the carrier board file is set_tc_clocks()
, which configures the timer/counter blocks for constant frequency clock outputs on the two dedicated clock output pins on the module. If these are not required for the hardware design, they may be disabled. Assume that the NPD board does not utilize these clocks and remove the function from the file altogether.
GPIO Support
The next section of the carrier board support file sets up GPIO devices using the EMAC GPIO Class. This involves setting up a collection of functions and arrays for each GPIO device and using the GPIO_SET_FUNCTION_CREATE()
macro as defined in gpio-wrapper.h
to define a complete GPIO class device. The following GPIO class devices are included in the SoM-210ES carrier support code:
sdsw
creates a GPIO device for toggling power to the SD card on the carrier boardgpio
creates a generic device using the lines labeled Handy GPIO pins on the SoM210ES headerrs232_4xx
controls the serial port configuration lines on the carrier boardbeeper
creates a method to toggle the input line to the beeper on the carrier board
Assume that the NPD hardware requires the sdsw
and rs232_4xx
features, but does not have the beeper or generic "Handy" GPIO header. Instead, a 3:8 analog multiplexer is provided on the SoM lines GPIO11, GPIO12, and GPIO13, which correspond to CPU pins PB14, PB15, and PB16 (see the SoM-9G45M manual). The resulting GPIO support code is as follows:
/* SD card power switch */
static unsigned sdsw_gpio_set[] = { AT91_PIN_PD10 };
static unsigned sdsw_direction = 0x01; /* output */
static unsigned sdsw_value = 0x00; /* low */
GPIO_SET_FUNCTION_CREATE(sdsw)
/* Analog mux control */
static unsigned amux_gpio_set[] = {
AT91_PIN_PB14, /* SOM GPIO11 */
AT91_PIN_PB15, /* SOM GPIO12 */
AT91_PIN_PB16, /* SOM GPIO13 */
};
static unsigned amux_direction = 0x0F; /* Default: All outputs */
static unsigned amux_value = 0x00; /* Default: Output low */
GPIO_SET_FUNCTION_CREATE(amux)
static unsigned rs232_4xx_gpio_set[] = {
AT91_PIN_PB24,
AT91_PIN_PB25,
AT91_PIN_PE0,
};
static unsigned rs232_4xx_direction = 0x07;
static unsigned rs232_4xx_value = 0x01; /* Default to RS232 */
GPIO_SET_FUNCTION_CREATE(rs232_4xx)
Boardspec
The EMAC boardspec
platform driver is used to specify board specific initialization code, such as GPIO class devices. A function pointer is passed into the platform device structure for the driver and called when the driver is loaded. carrier_classes()
is utilized in this case as seen below.
/*
* Boardspec IOEX
*/
static int carrier_classes(void)
{
/* SD Power */
sdsw_gpio_class_create();
/* RS-232/422/485 Control */
rs232_4xx_gpio_class_create();
/* Analog mux */
amux_gpio_class_create();
return 0;
}
static struct platform_device boardspec_device = {
.name = "boardspec",
.id = 2,
.dev = {
.platform_data = &carrier_classes,
},
};
static inline void carrier_device_boardspec(void)
{
at91_set_gpio_output(AT91_PIN_PE1, 1); /* LCD Enable */
platform_device_register(&boardspec_device);
}
Carrier Initialization
The final function in the carrier board specification file is carrier_init()
. This function is called from the SoM board file and initializes the carrier_spec
structure. This includes setting the use_periph
mask value to denote which devices are supported as well as initializing function pointers and other data specific to this carrier definition. The code from the board-som210.c
file may be used without modification to support the NPD board. This code is listed below.
int __init carrier_init(struct carrier_spec *spec)
{
spec->use_periph = CARRIER_USES_USBH | CARRIER_USES_MCI | \
CARRIER_USES_TSADCC | CARRIER_USES_PWM | \
CARRIER_USES_LCD | CARRIER_USES_SPI | \
CARRIER_USES_I2C0;
spec->carrier_map_io = carrier_map_io;
spec->carrier_boardspec = carrier_device_boardspec;
spec->carrier_spi_info = carrier_spi_devices;
spec->carrier_spi_cnt = ARRAY_SIZE(carrier_spi_devices);
return 0;
}
Testing
After making the development changes required to support a new carrier board, you must change the kernel configuration to specify the new carrier board. Using the menu configuration utility described in the Menuconfig section, navigate to 'System Type -> Atmel AT91 System-on-Chip -> EMAC Carrier Board Selection. The list should now have a choice for NPD Carrier Support. Highlight this option and press enter. Finally, exit and save the configuration.
Following the steps described in Building and Deployment above, compile the kernel and load it to your target hardware. Test all functionality, particularly new devices that were added to the carrier board support file, and make adjustments as necessary.
Driver Development
Device drivers provide a direct interface to a hardware device through a well-defined standard programming API. This makes the device accessible to userspace and other kernel code without requiring any knowledge of what is happening at the hardware level. For example, a CAN bus controller may be memory mapped to the processor, while another connects through the SPI bus. The user does not need to know which method is used, the CAN API is used to abstract this and the same application code may be used with either device. Furthermore, the driver for the SPI-based CAN chip may be used on different systems without porting as it uses the standard SPI API to interface with the SPI controller through the SPI driver written for the processor it is being used on. Developing and examining device driver code is often required through the course of embedded systems development, particularly due to the specialized devices used. This section provides a quick overview of device driver development on the Linux Kernel.
Driver Structure
As an open source operating system, all of the source code for device drivers on the system (except for any proprietary binary modules as discussed in Licensing below) are available for reference and analysis.
Driver Development Process
Licensing
It is important to note that all code built-in to the kernel automatically fall under the the GPLv2 license and must use an Open Source license compatible with the terms of the GPL. For loadable kernel modules, there is controversy over whether modules are derived works of the kernel. While proprietary and other non-GPL-compatible modules are generally permitted, several restrictions apply: The "taint" flag will be set on the kernel as soon as the module is loaded, and certain symbols are only available to modules marked with a GPL-compatible license.
EMAC recommends that you seek legal advice if you are unsure of the license requirements for your software.
See the following resources for more information:
Where to go for Additional Information
There is an abundance of information available both online and in-print on the topic of Linux kernel development. Some of these resources are discussed below.
- Kernel.org
- Kernel.org is the site hosting the Linux kernel. Source code, news, links, and other helpful information related to the Linux kernel can be found on this site.
- Linux Device Drivers, Third Edition (LDD3)
- This book is available online in free PDF form through the LWN.net site. It is also available in-print through O'Reilly. LDD3 covers most of the topics required for Linux kernel development and includes examples. Note that some of the APIs covered have changed since 2.6.10 when the book was written so adaptation may be required to use the example code.
- Mailing Lists
- There are many very active mailing lists (see http://vger.kernel.org/vger-lists.html) that can be used to ask questions or search through archives for solutions. The archive of the Linux Kernel mailing list is available at LKML.org and archives to other lists can be found through a web search as well as links noted in the list here.
- Linux Kernel in a Nutshell
- This book is written by Greg Kroah-Hartman, one of the primary developers and maintainers of the kernel and covers the process and tools for building, configuration, and installation of the Linux kernel. It is available for free through the authors site in electronic format or in-print through O'Reilly.
- EMAC Support
- EMAC provides custom Linux kernel development and kernel development support for EMAC customers on a contractual basis. Contact EMAC Support for more information.