Difference between revisions of "Example MikroBus Rotary on the iMX6U-112"
(Created page with "{{todo|SEOKWREV (01.02.14-14:09->JG+);(01.02.14-14:30->MD+);(01.02.14-16:15->MG+);(04.04.14-15:40->BS+)|Jgreene|project=oe 4,oe 5,jg,md,SEOKWREV,mg,bs}} {{#seo: |title=Exampl...") |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 2: | Line 2: | ||
{{#seo: | {{#seo: | ||
| − | |title=Example MikroBus Rotary on the | + | |title=Example MikroBus Rotary on the DEV-IOT6U |
|titlemode=append | |titlemode=append | ||
| − | |keywords=Example MikroBus Rotary on the | + | |keywords=Example MikroBus Rotary on the DEV-IOT6U,Using MikroBus Rotary on the DEV-IOT6U,EMAC C example project |
|description=This is a guide to the <code>MikroBus Rotary on the iMX6U-112</code> C example project. | |description=This is a guide to the <code>MikroBus Rotary on the iMX6U-112</code> C example project. | ||
}} | }} | ||
This is a guide to the MikroBus Rotary Demo on the iMX6U-112 IIoT Development Kit. | This is a guide to the MikroBus Rotary Demo on the iMX6U-112 IIoT Development Kit. | ||
{{note | Do to a design flaw in the MikroBus Rotary B Click, the card does not allow another SPI device to be present on the SPI Bus. The SoM-IMX6U uses the SPI Bus and the presence of MikroBus Rotary B Card prohibits the SOM from booting. | {{note | Do to a design flaw in the MikroBus Rotary B Click, the card does not allow another SPI device to be present on the SPI Bus. The SoM-IMX6U uses the SPI Bus and the presence of MikroBus Rotary B Card prohibits the SOM from booting. | ||
| − | '''To alleviate this issue, the pin labeled “SDO” must be cut and jumpers JB5 and JB6 must be set to 3P3''' (see figures below)}} | + | '''To alleviate this issue, the pin labeled “SDO” must be cut and jumpers JB5 and JB6 on the Dev Kit Carrier Board (SoM-112) must be set to 3P3''' (see figures below)}} |
| − | |||
| − | * The | + | == General Information == |
| + | === Hardware Requirements=== | ||
| + | |||
| + | * The DEV-IOT6U Development Kit | ||
| + | * Desktop PC (Windows/Linux/Mac will work) | ||
===Software Requirments=== | ===Software Requirments=== | ||
| − | These tools should already be installed if you installed the EMAC SDK using the automatic installer. | + | These tools should already be installed if you installed the EMAC SDK using [[Getting_Started_with_the_EMAC_OE_SDK#Installing_EMAC_SDK|the automatic installer]]. |
| − | * | + | * EMAC OE 5.X SDK |
* EMAC Qt Creator | * EMAC Qt Creator | ||
* GNU <code>make</code> | * GNU <code>make</code> | ||
| Line 23: | Line 26: | ||
=== Setup === | === Setup === | ||
| − | If you haven't already, please review the | + | If you haven't already, please review the [[Getting_Started_with_the_DEV-IOT6U| "getting started" page]] for the DEV-IOT6U. EMAC_OE_SDK will need to be installed and serial and network connections will need to be established between the developer machine and the target device. See the [[Serial Connections]] or [[Network Connections]] page for more information on how to connect to the target EMAC product using a serial port or Ethernet connection. |
| − | + | *Download this file | |
| − | Download this file | + | *Open a terminal and minicom/putty into the board |
| − | Open a terminal and minicom/putty into the board | + | *get the ip address |
| − | get the ip address | + | *second terminal |
| − | second terminal | + | *use EMAC OE SDK guide for host compiling |
| − | use EMAC OE SDK guide for host compiling | ||
| − | |||
==Usage and Behavior== | ==Usage and Behavior== | ||
| − | + | ===Using the Demo== | |
| − | + | In a terminal session with the iMX6U-112: | |
| − | === | + | <code> |
| − | + | ./name | |
| − | + | </code> | |
| + | The MikroBus Rotary dial may then be turned, and with each click, the lights with increment in binary. One side of the card's lights are associated with one of the card's registers, likewise for the other set of lights. | ||
==Summary== | ==Summary== | ||
asdf | asdf | ||
Latest revision as of 09:12, 14 September 2020
This is a guide to the MikroBus Rotary Demo on the iMX6U-112 IIoT Development Kit.
| NOTE |
| Do to a design flaw in the MikroBus Rotary B Click, the card does not allow another SPI device to be present on the SPI Bus. The SoM-IMX6U uses the SPI Bus and the presence of MikroBus Rotary B Card prohibits the SOM from booting. To alleviate this issue, the pin labeled “SDO” must be cut and jumpers JB5 and JB6 on the Dev Kit Carrier Board (SoM-112) must be set to 3P3 (see figures below) |
Contents
General Information
Hardware Requirements
- The DEV-IOT6U Development Kit
- Desktop PC (Windows/Linux/Mac will work)
Software Requirments
These tools should already be installed if you installed the EMAC SDK using the automatic installer.
- EMAC OE 5.X SDK
- EMAC Qt Creator
- GNU
make - CMake
Setup
If you haven't already, please review the "getting started" page for the DEV-IOT6U. EMAC_OE_SDK will need to be installed and serial and network connections will need to be established between the developer machine and the target device. See the Serial Connections or Network Connections page for more information on how to connect to the target EMAC product using a serial port or Ethernet connection.
- Download this file
- Open a terminal and minicom/putty into the board
- get the ip address
- second terminal
- use EMAC OE SDK guide for host compiling
Usage and Behavior
=Using the Demo
In a terminal session with the iMX6U-112:
./name
The MikroBus Rotary dial may then be turned, and with each click, the lights with increment in binary. One side of the card's lights are associated with one of the card's registers, likewise for the other set of lights.
Summary
asdf
