Wifi

From wiki.emacinc.com
Revision as of 16:38, 28 October 2015 by Mdean (talk | contribs) (Made various fixes and comments, and marked as Buggy.)
Jump to: navigation, search
TODO: {{#todo:Buggy (10.20.2015-14:23->JJ+);(10.20.2015-13:43->JJ+);(10.23.2015-11:50->MD-);(10.26.2015-16:50->JJ+);(10.27.2015-15:30->JJ+); (10.28.2015-15:05->JJ+);(10.28.2015-16:35->MD-)|Jeffrey Jung|OE 5.0,Buggy,JJ,MD}}



WARNING!
Keywords need to be added to the SEO tag (above)


This guide will illustrate how to set up and connect to a wireless network using the ThinkPenguin Wireless N USB Adapter for GNU/Linux and the built-in WiFi on the SoM-200GS.


Background

While many machines from EMAC are not natively designed to connect to wireless networks, most of these systems do have USB ports. Using a USB wireless network adapter, like the one found here at ThinkPenguin, a system can equipped with wireless networking capability.

This page describes the actions needed to connect to a wireless network either using either a wireless network USB adapter, or the built-in Wi-Fi found on EMAC products like the SoM-200GS carrier. We chose to use the ThinkPenguin USB adapter for this page because it is well supported by the Linux kernel.


General Information

Set Up

Before the device can be connected to the network, some additional software will need to be installed. In order to obtain the new packages, connect the system to a physical network. If your are going to be using the USB adapter for the connection, it may be plugged in at this time, although it may not have the proper drivers installed to the system yet.



WARNING!
This step isn't needed on EMAC boards with built in wifi capability. Boards like the SOM-200GS with the wifi option will have this software pre-installed. You can tell them to skip this section for those boards.


  1. This process requires modifying some system files, so start by enabling read and write permissions to the filesystem.

    root@ipac9x25:~# mount -o remount,rw /
  2. A check for any updates is typically a good practice before installing new software. Use the opkg manager to install any updated software from the package list.

    root@ipac9x25:~# opkg update
  3. One of the best tools to establish the connection to wireless networks is the wpa-supplicant package. This supplicant will allow the system to make connections to WPA and WPA2 protected networks. Install this package with the opkg manager.

    root@ipac9x25:~# opkg install wpa-supplicant
  4. If using the USB adapter, the appropriate drivers may need to be installed. The ThinkPenguin USB adapter requires the installment of the linux-firmware-ath9k package.

    root@ipac9x25:~# opkg install linux-firmware-ath9k



    WARNING!
    Don't forget to always use code tags around package names. I added them around linux-firmware-ath9k for you.


    Also, don't forget to capitalize and double check the spelling of company names; I fixed Marvell below; it was "marvel". The package name apparently misspells the company name.

    Additionally, the Marvell package won't work for all EMAC products with built in Wifi. I'm currently designing a board which will have a Texas Instruments Wifi module on it rather than the wi2wi module which uses the Marvell driver. But as I mentioned above, the board should have this pre-installed. If it doesn't, please let me know. It's important that this software and the correct drivers are pre-installed on these boards.

    Showing example output of the opkg commands, below, will make the procedure more clear.


  5. If using built-in Wi-Fi, the Marvell license and linux-firmware-sd8787 packages will need to be installed.

    root@som9g45:~# opkg install linux-firmware-marvel-license
    root@som9g45:~# opkg install linux-firmware-sd8787
  6. Independent of using built-in Wi-Fi or an adapter, the iw and wireless-tools packages will complete the needed software to get a connection started.

    root@ipac9x25:~# opgk install iw
    root@ipac9x25:~# opkg install wireless-tools
  7. Upon successful installation of all required packages, the system will need to be rebooted to take advantage of the new packages.

    root@ipac9x25:~# reboot


Wireless Networking

Using the packages that have just been installed, the system can be connected to the wireless network.

  1. Changes to some configuration files will be necessary, so remount the root filesystem with read and write permissions.

    root@ipac9x25:~# mount -o remount,rw /
  2. Wireless networks can be found using the scan option of iw.

    root@ipac9x25:~# iw dev wlan0 scan
    A detailed list of the nearby networks will be printed out to the terminal. To identify the SSIDs and respective signal strengths of the network(s) more easily, pipe the output of the iw scan command through grep to scan for the keywords "SSID" or "signal". The closer the value of the signal strength is to 0, the stronger the connection.
    root@ipac9x25:~# iw dev wlan0 scan
    SSID: EMAC-A
    root@ipac9x25:~# iw dev wlan0 scan
    signal: -78.00dBm
    root@ipac9x25:~#



    WARNING!
    Did you forget to add the greps to the above commands? Oh wait, no, you stumbled across a gotcha in the wiki syntax. You can see several examples of how I worked around this by looking at the source, here: http://wikidev.emacinc.com/wiki/Opkg#Finding_Packages_to_Install



    The /etc/wpa_supplicant.conf file will need to be modified to provide the necessary connection information, the details of which depend upon the type of encryption used for the wireless network.

  3. For an open network, uncomment the following lines in /etc/wpa_supplicant.conf and fill in the correct SSID for the network to which the machine should connect.

    ###open network
    #network={
    #      ssid="SSID"
    #      scan_ssid=1
    #       key_mgmt=NONE
    #}
    
  4. Networks protected by either WEP or WPA2 encryption will need a pre-shared key (PSK), which is generated for the specific network and its password. To get the PSK, use wpa_passphrase with the SSID and password for the desired network as arguments and redirect the output to a new file, /etc/wpa_supplicant.conf. Note: if this file already exists, it will be overwritten by this command; you may want to back it up first.

    root@ipac9x25:~# wpa_passphrase SSID Password > /etc/wpa_supplicant.conf
    root@ipac9x25:~#
  5. The contents of the /etc/wpa_supplicant.conf should now look similar to the following:

    root@ipac9x25:~# cat /etc/wpa_supplicant.conf

    network={

    ssid="SSID"
    #psk="Password"
    psk=b99d2c0fb66194f93ad52b71051e1095dc76e12529321334b3feb18332608eb7

    }

    root@ipac9x25:~#



  6. The root@som9x25:~# /etc/init.d/wpa_supplicant start command will attempt to establish a connection with the network.

    As the command is running, watch the terminal output for the status of the connection. A connection has been established when output stops and the last line reads:
    IPv6 ADDRCONF(NETDEV_CHANGE):wlan0: link becomes ready


    A connection has failed if output to the terminal continues and the following line is seen repeatedly:
    IPv6: ADDRCONF(NETDEV_UP):wlan0: link is not ready


    Successful connection (waiting a full minute to ensure output to the terminal stopped);
    root@ipac9x25:~# /etc/init.d/wpa-supplicant start

    Successfully initialized wpa_supplicant
    rfkill: Cannot open RFKILL control device

    root@ipac9x25:~# wlan0: authenticate with 1c:7e:e5:40:10:fd

    wlan0: send auth to 1c:7e:e5:40:10:fd (try 1/3)
    wlan0: send auth to 1c:7e:e5:40:10:fd (try 2/3)
    wlan0: authenticated
    wlan0: associating with AP with corrupt beacon
    wlan0: associate with 1c:7e:e5:40:10:fd (try 1/3)
    wlan0: RX AssocResp from 1c:7e:e5:40:10:fd (capab=0x431 status=0 aid=6)
    wlan0: associated
    IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

    Failed connection (waiting more than a minute as output continues to print to the terminal). The repeated lines indicate an issue establishing the connection.
    root@ipac9x25:~# /etc/init.d/wpa-supplicant start

    Successfully initialized wpa_supplicant IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

    root@ipac9x25:~# IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

    cfg80211: Calling CRDA to update world regulatory domain
    IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    cfg80211: Calling CRDA to update world regulatory domain
    IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    cfg80211: Calling CRDA to update world regulatory domain
    IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    cfg80211: Calling CRDA to update world regulatory domain
    IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    cfg80211: Calling CRDA to update world regulatory domain
    IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    cfg80211: Calling CRDA to update world regulatory domain
    IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    cfg80211: Calling CRDA to update world regulatory domain
    IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

    A failed connection is likely the result of an improper password. Use wpa_passphrase to make sure you have the right psk for the password.


  7. The ifconfig command will be used to determine that the device is wirelessly connected to the network. Look to see that wlan0 has an IP address.

    wlan0 Link encap:Ethernet HWaddr A8:54:B2:42:89:8D

    inet addr:10.0.4.148 Bcast:10.0.255.255 Mask:255.255.0.0
    UP BROADCAST RUNNING MULTICAST MTU:1500 METRIC:1
    RX packets:3395 errors:0 dropped:6 overruns:0 frame:0
    TX packets:60 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:346619 (338.4 KiB) TX bytes:6318 (6.1 Kib)


  8. Disconnect any physical connections from the system and ping to www.emacinc.com to verify that the system can wirelessly connect to the Internet.

    root@ipac9x25:~# ping -c www.emacinc.com

    PING www.emacinc.com (172.16.0.10): 56 data bytes
    64 bytes from 172.16.0.10: seq=0 ttl=63 time=1.910 ms
    64 bytes from 172.16.0.10: seq=1 ttl=63 time=1.748 ms
    64 bytes from 172.16.0.10: seq=2 ttl=63 time=2.061 ms

    --- www.emacinc.com ping statistics ---
    3 packets transmitted, 3 packets received, 0% packet loss
    round-trip min/avg/max = 1.748/1.906/2.061 ms

    root@ipac9x25:~#




WARNING!
Adding troubleshooting steps, such as checking /etc/resolv.conf to see what DNS server(s) were provided from the DHCP server, and inspecting the routing table, would be beneficial.


Conclusion

This page walks through the procedure to connect a machine to a wireless network via a USB Wifi adapter or built-in wireless, as well as acquiring the necessary software tools to make the connection for the first time. While there are plenty of USB wireless adapters available for sale, we used an adapter intended for use on Linux machines with a driver supported by the EMAC OE SDK. Other USB wireless adapters may be used to connect EMAC devices to wireless networks, but they will often face issues with driver support or other compatibility issues. We recommend using a USB adapter from ThinkPenguin.



WARNING!
Should we really recommend buying an adapter from a 3rd party? This is generally not a good business practice. Eric?


After connecting to a network the first time, the system will be able to connect to the same network when rebooted or powered on. Connecting to a new network will require going through the procedures set out under the Wireless Networking section.



WARNING!
The moreinfo template section should be filled in with links to other articles we have on networking, since other articles do apply.



Pages with Related Content