Difference between revisions of "Xenomai RTNet"

From wiki.emacinc.com
Jump to: navigation, search
Line 50: Line 50:
  
 
The rtnet helper script is configured with /etc/rtnet.conf which determines the IP address of the interface and the slave devices.
 
The rtnet helper script is configured with /etc/rtnet.conf which determines the IP address of the interface and the slave devices.
 +
The real-time driver is also specified in the configuration file so that it does not need to be loaded before starting the script but the Linux driver still must be disassociated with the interface.
 +
 +
 +
=== Accessing RTNet driver ===
 +
 +
Xenomai provide real-time versions of the basic networking utilities including rtifconfig, rtping, rtroute and rtiwconfig.
  
 
<syntaxhighlight lang="console">
 
<syntaxhighlight lang="console">
Line 65: Line 71:
 
           UP LOOPBACK RUNNING  MTU: 1500
 
           UP LOOPBACK RUNNING  MTU: 1500
 
</syntaxhighlight>
 
</syntaxhighlight>
 +
  
  

Revision as of 13:34, 7 March 2016

TODO: {{#todo: NotStarted (03.03.2016-13:06->MW+)|Michael Welling|OE 5.0,MW,NotStarted}}

General Information

Xenomai uses the RTNet stack to provide real-time Ethernet. RTNet provides deterministic versions of various protocols (UDP/IP, IMCP, ARP). Xenomai provides several real-time Ethernet drivers, the stack, and various tools. This document explains how to load a real-time Ethernet driver and perform basic tests. The links below will help augment this information as well as discuss programming using the RTnet stack.

Xenomai RTNet

Loading a RTNet driver

As with the other real-time drivers, the Linux driver must be detached the interface before loading that real-time driver.

For example on IMX6 target the fec device must be unbound from the Linux driver and attached to the real-time driver.

root@somimx6-xenomai:~# echo 2188000.ethernet > /sys/bus/platform/drivers/fec/unbind 
root@somimx6-xenomai:~# echo 2188000.ethernet > /sys/bus/platform/drivers/rt_fec/bind
[   86.762295] libphy: fec_enet_mii_bus: probed
[   86.766586] RTnet: registered rteth0

Xenomai provides a script make launching rtnet easier. This will load the appropriate modules and bring up the interface.

root@somimx6-xenomai:~# rtnet -cf /etc/rtnet.conf start
[  645.330848] initializing loopback...
[  645.334487] RTnet: registered rtlo[  645.355662] RTcfg: init real-time configuration distribution protocol
[  645.375986] RTmac: init realtime media access control[  645.400419] RTmac/TDMA: init time division multiple access control mechanism
[  645.499423] rteth0: Freescale FEC PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
[  645.551954] rteth0: tx link down!.
...
[  652.497075] rt_fec 2188000.ethernet (unnamed net_device) (uninitialized): Link is Up - 1Gbps/Full - flow control rx/tx

The rtnet helper script is configured with /etc/rtnet.conf which determines the IP address of the interface and the slave devices. The real-time driver is also specified in the configuration file so that it does not need to be loaded before starting the script but the Linux driver still must be disassociated with the interface.


Accessing RTNet driver

Xenomai provide real-time versions of the basic networking utilities including rtifconfig, rtping, rtroute and rtiwconfig.

root@somimx6-xenomai:/# rtifconfig
 rteth0    Medium: Ethernet  Hardware address: 00:00:00:00:00:00
          IP address: 10.0.0.1  Broadcast address: 10.255.255.255
          UP BROADCAST RUNNING  MTU: 1500
          RX packets:14 errors:0 dropped:0 overruns:0 frame:0
          TX packets:164476 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 
          RX bytes:896 (896.0 b)  TX bytes:7031954 (6.7 Mb)

rtlo      Medium: Local Loopback
          IP address: 127.0.0.1  
          UP LOOPBACK RUNNING  MTU: 1500


External Links